
PowerPro 164Si
The PowerPro 164Si is clearly a great choice for the person needing a modestly powered welding package that offers a little bit of everything. It is perfectly suited for the home garage, small fabrication facility or portable repair business. The all new digital IGBT inverter design features 120/240V input for true go anywhere performance. Digital control has improved operation and reliability over the previous PowerPro 164 models while increasing precision of adjustments. If you need true portability for on-the-site welding and cutting or occasional light fabrication chores, the PowerPro 164Si is well equipped to handle your needs, with TIG, Stick and Plasma cutting features. The TIG mode also features full adjustability of the AC output with AC frequency and AC balance controls to offer the maximum quality weld. When you add the simple 2 speed TIG pulse feature, this unit gives you plenty of capability. At the power level this unit puts out, it's able to weld up to 3/16" aluminum and 1/4" steel in a single pass in TIG mode, and handle many common 1/8" stick electrodes. The stick feature offers stick welding power up to 130 amps, enough power for general duty welding up to 1/8" electrodes when TIG welding just isn't possible, and where TIG isn't the best solution. The 40 amp plasma is good for regularly cutting metal up to 3/8" thick with severance capability up to 5/8" thick. This unit also features a generous 60% duty cycle in TIG mode at full power, so there's more welding being done than sitting around waiting for the unit to recover.
Features & Benefits | Features & Benefits:
|
---|---|
What's Included | Standard Equipment:
|
Tech Specs | Tech Specs IGBT Inverter Type:
IGBT
Voltage/phase:
Dual Voltage 120/240 1 Phase
TIG output type:
AC/DC
TIG Start Type:
High Frequency only
Pulse:
Yes, Fixed 2 position
Plasma Cutter Arc Start Type:
Blow Back (Piston type)
PilotArc:
Yes
OK-to-Cut Indicator/Low Air pressure safety:
Yes
AC Frequency:
20-250 Hz AC Balance (cleaning):
10-90% OCV:
85V TIG/Stick, 290V Plasma Max Inrush ( I1MAX ) Amps:
Maximum Rated (I1EFF ) Input Amps:
TIG Output Amps/Volts @ Rated Duty Cycle:
120V:
240V:
Stick Output Amps/Volts @ Rated Duty Cycle:
120V:
240V:
Plasma Output Amps/Volts @ Rated Duty Cycle:
120V:
240V:
TIG AC Amp/Volt Range:
TIG DC Amp/Volt Range:
Stick Amp/Volt Range:
Plasma Amp/Volt Range:
Start Amps:
Fixed, Minimum End Amps:
Fixed, Minimum Down Slope Time:
0-10 Seconds Up Slope Time:
Fixed, Minimum Preflow time:
Fixed, .5 Seconds Post Flow Time:
0-10 Seconds OverCurrent Protection:
Yes Duty Cycle Protection:
Yes Air Pressure OK Safety Indicator:
Yes TIG Pulse Frequency:
1Hz or 25 Hz (Fixed 2 speed) TIG Pulse Time On:
Fixed, 50% TIG Pulse Amp Range:
Fixed, 50% Stick Arc Force Control:
6010/Cellulose Capablel:
No. Torch Type:
S-45 Recommended Cutting Air Pressure:
75 PSI Recommended Compressor Capacity:
4 CFM or greater, 20 gallon |
Minimum Maxmimum | Minimum/Maximum:TIG single pass capability:
Stick electrode diameter capability:
Plasma Cutting capability* ( with dry air, new consumables, proper air pressure etc.):
*Quality and capacity of cut depends upon consumable orifice size, standoff height, travel speed, etc. |
Optional Equipment | Optional Equipment:
|
Notes | Product Notes: For generator use: Use only generators that are certified as "clean power" by the manufacturer. This means that the unit has less than 5% THD (total harmonic distortion) |