In stock
Special Price CA$1,150.00 Regular Price CA$1,450.00
Plasma Cutters

Make a list of everything you want in a plasma cutter.  Chances are that you'll come up with a list that matches up pretty closely to the list of features of the Everlast PowerPlasma 62i.  It has has the convenience, portability and performance that will meet the needs of everyone from the weekend enthusiast to the welding and fabrication shop.  The PowerPlasma 62i is built on an inverter platform, making use of IGBT modules from Infineon (Siemens) to reduce weight, and improve reliability and performance over the individual IGBT design.   The unit has plenty of cut capacity with a recommended 9/16" daily cut, a 3/4" clean cut ,1" severance cut and up to 3/8" CNC.  The new iPT 60 torch (4m) is part of the standard package and features a proven long life Italian design with blow back start, pilot arc and a variety of consumable choices.  The PowerPlasma 62i features a 3 second tip saver to reduce premature consumable wear by limiting pilot arc on time, if no cutting is taking place.

More Information
Features & Benefits

Features & Benefits:

  • New Bezel and stackable feature!
  • IGBT Inverter Plasma Cutter
  • Easy starting with Blow Back Pilot arc allows easy cutting of rusty and painted metals
  • Cuts virtually any type of metal with ease
  • 60% Duty cycle at 60 amps
  • iPT 60 Torch
  • Blowback start starts arc without the need of High Frequency which can interfere with surrounding electronics
  • Pilot arc improves performance and cutting on dirty, painted, or rusted metals 
  • 3 Second pilot arc tip saver feature shuts down pilot arc after 3 seconds of continuous operation
  • Digital readout for air pressure, allows quick verification of air pressure
  • Over Current and Duty Cycle protection indicates fault with a dedicated warning/diagnostic light, and shuts down output until condition is resolved
  • Adjustable postflow timer for maximum consumable life
  • CNC socket for CNC use on plasma tables (machine torch optional)
  • NOTE: When used with a generator, the generator must be certified by its manufacturer to produce "clean" power (5% or less THD)
What's Included

Standard Equipment:

  • iPT60 - 4m Hand Held Plasma Torch with Euro quick-connect central adapter
  • Work clamp with 3m cable and 25 series DINSE style connector
  • Regulator/Water trap (this is not an air dryer)
  • Consumable Starter Kit
  • 1.8m Power input cable with NEMA 6-50 Plug
Tech Specs

Tech Specs

220/240 V 1 Phase
Output Amp/Volt Range: 

20-60A; 88-104V



Max Inrush ( I1MAX ) Amps: 


Maximum Rated (I1EFF ) Input Amps: 


Duty Cycle At Rated Amps/Volts: 
  • 60% @ 60A/104V
  • 100% @ 50A/100V
Arc Start Type: 
Blow Back (Piston type)
Weight: 58 lb
Torch Type: 

Italian designed iPT 60i

CNC Interface Port: 


Adjustable Post Flow Timer: 
Light to Medium | Requires Gouging Consumables (Not Recommended)
Recommended Cutting Air Pressure: 

75 psi

Recommended Compressor Capacity: 

6CFM @ 90 psi/ 30 gallon tank

OK-to-Cut Indicator/Low Air pressure safety: 
Minimum Maxmimum


  • Up to 9/16" daily use @ 15-20 ipm
  • Up to 3/4" clean cut @ 8-12 ipm
  • Up to 1" severance cut @ 3-5 ipm
  • Max Pierce CNC Up to 3/8"

Plasma cutting quality + capacity is affected by several factors.

Optional Equipment

Optional Equipment:

  • Welding cart
  • Welder Cover
  • Consumable kit

Product Notes:

To improve consumable life and prevent torch damage, the customer must supply and install a separate air dryer inline in addition to the regulator/water trap supplied by Everlast. The water trap Everlast supplies with the unit is not designed to remove all moisture from the air.

Disclaimer: "Units and accessories may not be exactly as pictured"